Bonding to cement-based and suitably prepared calcium sulphate based screeds, concrete, plywood overlaid floors, existing unglazed ceramic floor tiles, cement-based renders, gypsum plaster, plasterboard.
FULL PALLET - 48 x 20kg & 48 x 6kg - FREE ECONOMY DELIVERY (Approx. 2-3 WORKING DAYS)*
*Full pallet deals are shipped directly from Mapei. For same day despatch, orders need to be placed before 12.30pm. A tail-lift will be specified for the unloading of the pallet. Please include any important delivery instructions/access in the "Notes" when completing your order.
Next Day Delivery is available for £42 (including VAT).
Bonding to cement-based and suitably prepared calcium sulphate based screeds, concrete, plywood overlaid floors, existing unglazed ceramic floor tiles, cement-based renders, gypsum plaster, plasterboard, tilebacker boards.
Note: When fixing tiles at lower temperatures the pot life and setting time may be extended beyond 2 hours. In autumn / winter temperatures only fix tiles when the substrate and ambient temperature is above +5ºC. When fixing externally ensure that the adhesive is applied during the warmest part of the day and that it will have cured sufficiently before temperatures drop below +5ºC. Protect exposed tiled areas from frost by covering with appropriate materials.
Keraquick S1 is a grey or white powder composed of a blend of special cements, selectively graded aggregates, synthetic resins and accelerators, which develop high bond strength 2-3 hours after mixing.
These properties allow floors and walls tiled using Keraquick S1 to be grouted after only 2 hours. Floors can also be subjected to light foot traffic after 2 hours and full service conditions after 24 hours. Where floors are to be subjected to heavy duty use, such as cherry pickers, the floor tiling should have been allowed to cure for a minimum of 7 days.
RECOMMENDATIONS
Use Keraquick S1 mixed with Latex Plus in the following cases:
Do not use Keraquick S1 in the following cases:
Preparation of the substrate
Substrates must be dry, flat, mechanically strong, sound, free from loose areas, grease, oil, paint, wax, old flooring adhesive and bitumen residues and any other contamination(e.g. plaster droppings), which may affect the adhesion. Damp substrates may lengthen Keraquick S1’s setting time.
Cementitious substrates must be cured and any shrinkage process must be at an end before tiles are installed. Renders should be cured for at least 2 weeks, concrete at least 6 weeks old, cement based screeds for at least 3 weeks unless they have been produced using the special MAPEI binders Mapecem or Topcem or with a preblended screed mix such as Mapecem Pronto or Topcem Pronto. The substrate surface should ideally be open textured. Power floated concrete should be mechanically abraded (scabbled or shot-blasted) to open up the surface and to remove any curing agents.
Heated screeds must be commissioned in accordance with recognised technical regulations and the guidelines given in BS 5385 parts 3, 4 and 5. The commissioning process must be carried out before the installation of tiles or stone finishes.
Gypsum plaster should be at least 4 weeks old and primed with Primer G. Note: over-trowelled plaster surfaces should be lightly abraded to provide a key before priming. Calcium sulphate screeds must be dry to a moisture content of 0.5% w/w when measured using the carbide method. All surface laitance must be removed by mechanical abrasion and all dust thoroughly removed by vacuum. Prime the surface with Eco Prim T Plus (diluted 1:2 with water) or alternatively Primer G.
Plasterboard and tilebacker boards must be installed to provide a firm, stable substrate with no protruding fixings.
Plywood must be a minimum of 15 mm thick and screw fixed at maximum 300 mm centres on floors. It should be of class 3 in accordance with EN 314 and EN 636. Steel substrates must be well braced to provide a deflection free support. Remove all rust, mould oil, grease and other contamination. Apply a skim / scratch coat of Keraquick S1 mixed with Latex Plus and allow to set, then fix the tiles in a void free bed of the same product.
Mixing
A 20 kg bag of Keraquick S1 grey and white should be mixed with about 4.8-5.2 litres of water. Alternatively mix a 20 kg bag of grey or white Keraquick S1 with 6 kg of Latex Plus. Where other bag sizes are used, mix at a ratio of 1 kg powder to 0.25 litres of water or 0.3 litres Latex Plus. Pour clean water (or liquid) into a clean mixing bucket. Add Keraquick S1 powder and mechanically stir until a homogenous, lump-free paste is achieved. Allow the mix to stand for 2 minutes then briefly stir again. Use the mix within 30 minutes of preparation.
Applying the product
Apply the prepared Keraquick S1 to the substrate with a notched trowel to a maximum of 10 mm thick. To achieve good adhesion to the substrate, first apply a skim coat of adhesive over the substrate using the flat edge of the trowel followed by combing through with the notched edge of the trowel to the required thickness. Ensure that a minimum coverage of 65-70% to the back of the tile is achieved in dry wall areas with 100%, as far as possible, in wet walls areas, on floors and in exteriors (walls and floors). Ensure that a trowel with a notch size and profile appropriate to the size of tile is used. For demanding applications such as exterior tiling subject to freezing, swimming pools or water feature installations, heavy duty areas, floor tiling to be ground in situ, when installing tiles with deep recesses or lugs on the rear and for fixing large format tiles (> 300 x 300 mm), the adhesive should also be applied to the rear of the tile (back buttering).
For the installation of tiles greater than 600 x 600 mm we recommend the addition of Latex Plus to Keraquick S1. On highly absorbent substrates it is recommended to prime with e.g. Primer G and Eco Prim T Plus before commencing tiling.
Installing the tiles
Do not wet the tiles before installation; if, however, the backs are very dusty, they should be dipped in clean water. Allow to dry before fixing. Keraquick S1’s open time in normal temperature and humidity is about 15-20 minutes; unfavourable weather conditions (strong sun, drying wind, high temperature), or a highly absorbent substrate may shorten this open time, sometimes quite drastically, to just a few minutes. Constantly check to see whether the adhesive has formed a surface skin. Should a surface skin have formed, the adhesive should be removed and fresh material applied. It is not recommended to wet the adhesive when it has formed a skin because a non-adhesive film will be formed. Tiling installed with Keraquick S1 must not be subjected to was
Set to light foot traffic
Floors are able to take light foot traffic after 2-3 hours. Lower temperatures may extend the setting time.
