On Sale

Lithofin KF Protective Impregnator Porcelain Sealer - 1 Litre

This special impregnator effectively protects the surface against staining by inhibiting the penetration of water oil grease and dirt. Lithofin FZ Protective Impregnator does not affect the appearance of the surface.

Additional Products (Optional)

List Price: £42.95 inc.VAT
£32.93 inc.VAT (£27.44 ex.VAT)
(You save £10.02 )
Adding to cart… The item has been added
Available: In Stock (12)
  • Downloads

A special product from the LITHOFIN-Range for fully vitrifiedceramic and porcelain tiles (KF). Lithofin KF Protective Impregnator is a water based nearly odourless impregnator consisting of a combination of high quality water and oil resistant components.

Technical Data:
Density: approx. 1,0 g/cm³
Appearance: liquid, yellowish, clear
Odour: non specific
pH-Value: 3 to 6
Flash Point: >65°C
Solubility in Water: --

This special impregnator effectively protects the surface against staining by inhibiting the penetration of water, oil, grease and dirt. Lithofin KF Protective Impregnator does not affect the appearance of the surface.

Field of Use:
For protecting all newly laid absorbent polished and unglazed porcelain tiles in order to facilitate maintenance. Suitable for indoor and outdoor use.

Directions For Use:
The surface to be treated must be completely clean and dry. Shake Lithofin KF Protective Impregnator well before use. Apply undiluted with a clean cloth or a lambs wool roller and ensure even distribution by wiping (rolling) over the surface several times.

For best results, treat the surface in sections of approx 15m² at a time. After 10 to 20 minutes, completely remove any surface residues with a squeegee or with a dry cloth.

Attention! the liquid product must sink into the stone. Immediately wipe off puddles and drips. Do not allow the product to dry on the surface. Carefully remove all residues and check against back light.

Please Note: Impregnators are not suitable for all porcelain tiles. Always try the product in an incon-spicuous area prior to use. Protect glass, varnished surfaces, plastics, etc. against splashes.

Coverage: Up to 50m² per litre, depending on the absorbency of the surface.

Storage: Keep closed, cool and dry. Shelf life of at least 12 months. Open containers should be used quickly.

Environmental Protection: Solvent free, water based.
Disposal: Diluted product may be added to waste water.

Containers are made of environmentally friendly polyethylene (PE). Clean containers can be recycled through collection systems.

polymers; water; auxiliary agents.

General Information: keep out of the reach of children. Treated surfaces present no health hazard once dry.

First Aid Procedures: Remove contaminated soaked clothing immediately. In case of inhalation, ensure of fresh air.
In case of contact with skin wash off immediately with soap and water. In case of contact with eyes rinse thoroughly with plenty of water and seek medical advice. In case of ingestion, do not induce vomitting. If swallowed by mistake drink plenty of water and seek medical treatment.

Emergency Procedures: In case of spill or other release, take up with absorbent material (e.g. sand, sawdust, general-purpose binder). Ensure adequate ventilation. Product does not burn, fire-extinguishing activities according to surrounding. In case of fire formation of dangerous gases possible.

Additional Information is listed on the Material Safety Data Sheet. ADR2003: not a dangerous good

1 litre bottle with child-proof cap (10 per box)
5 litre canister (2 per box)

This information should be considered to be informal and non-binding. The products must be used according to local conditions and materials. Where no previous experience is available, or in cases of doubt, test the product in an inconspicuous area. (GB11.04gps/12.02)