Lithofin MN Stain Stop ECO Water Based Sealer - 1 Litre
Additional Products (Optional)
- Downloads Lithofin MN Stain Stop ECO Technical Data.pdf, Lithofin MN Stain Stop ECO Safety Data.pdf
This ready-to-use special impregnator is water based and nearly odourless. Highly active water and oil repellent polymers ensure that this easy to apply treatment offers optimal results. Lithofin MN Stain-Stop >ECO< provides the ultimate protection against water and oil stains and facilitates every-day maintenance.
Density: approx. 1.0 g/cm³ pH-Value: approx. 8
Appearance: clear, yellowish, liquid
Odour: nearly odourless Flash Point: n.a.
Lithofin MN Stain-Stop >ECO< penetrates into absorbent natural stone surfaces and coats the capilliaries with an extremely thin and invisible film of polymers. This film alters the surface tension of the surface, causing a repelling effect. The treatment prevents the immediate penetration of water based dirt as well as oil and grease, and it provides an effective protection against staining.
approx. four years depending on the type and use of the treated material.
Field of Use:
To protect absorbent natural stone against staining and to render surfaces water and oil repellent. Treatment is recommended for all stone surfaces, such as: floors in kitchen, dining and living areas. The surfaces can be polished, honed, or rough. Lithofin MN Stain-Stop >ECO< can be used as a grout release and as a pre-treatment. Suitable for indoor and outdoor use.
Absorbent natural stones, especially suitable for rough and honed limestone, polished and honed hardstone.
On siliceous stones with a rough surface (such as honed or flamed granite), dense limestone and in cases where the highest level of water repellency is required (eg. in the shower) we recommend using Lithofin MN Stain-Stop (solvent based). This also applies to surfaces that have been pre-treated with other products.
Directions for Use:
Check the suitability and effect with a test in an inconspicuous area or on a spare tile. The surface must be absorbent, completely dry, clean and free of stains. Shake bottle before use. Apply generously and evenly using a lambswool applicator, roller, lint free cloth or sponge. Ensure even distribution by wiping over several times. Ensure that all surface residues is removed within 15 min. by towelling them off, do not allow residues to dry on the surface. On highly absorbent surfaces, apply several coats wet-in-wet.
Approx. 3 hours. Treatment is fully effective after 48 hours. Do not cover surface before then and wipe up any spills immediately.
Some materials may appear slightly darker after treatment. If no prior product experience exists or in cases of doubt, we recommend a trial application. Immediately remove splashes on wood, glass, PVC, lacquered surfaces, etc. with a damp cloth. Clean application tools with water after use.
The temperature of the surface to be treated should not be under 10°C and not over 25°C. Throttle or turn off floor heating.
Honed limestone: 4-8m² per litre, polished natural stone: up to 20m².
In case a deep clean is required, use Lithofin MN Power-Clean diluted 1:20 and a white pad. Rinse well with plenty of water, since residues of cleaners may affect the effectiveness of the protective treatment. Impregnators do not protect the surface against acid.
Touching up the Protective Effect:
Surfaces subject to increased wear (such as surfaces in kitchen and bathroom) should be touched up at least once per year. This re-treatment can be done with Lithofin MN Stain-Stop >ECO< or with the solvent based Lithofin MN Stain-Stop. First give the surface a deep clean and allow it to dry for one day. Then simply wet a clean cloth with the impregnator and rub it into the surface.
Closed, cool and frost free Shelf life of up to 3 years. Open containers should be used up without delay.
Free of chlorinated and other environmentaly harmful hydrocarbons. The contained polymers are dissolved in water and inert once dry. Lithofin MN Stain-Stop >ECO< is therefore ecologically sound (>ECO<).
Containers are made of environmentally friendly polyethylene (PE) and are recyclable. Clean containers can be recycled through collection systems.
No health concerns once dry. Please keep out of reach for children.
Polymers, auxilliary agents, water. Hazordous materials regulations: According to EC Directive 1999/45/EG: none. ADR2003: not a dangerous good.
1 litre bottle with child-proof cap (10 per box)
5 litre canister (2 per box)
This information should be considered to be informal and non-binding. The products must be used according to local conditions and materials. Instructions must be read carefully and followed closely. Always test the product for suitability and effect prior to use. (GB3.09bs)